diy lantern light fixture

I’ve been holding out on you about our porch progress. See, while I was busy showing off this:

Outdoor Rug

I was hiding this:

Porch Ceiling Before

Ew.

In addition to the wonderful green tile on our screened porch, we had this a gorgeous florescent light, the kind that looks like it belongs in some derelict warehouse building. Obviously, it had to go.

Down the line, we’d really like to take out the whole ceiling and just have the exposed rafters for a nice open look. But we’re short on time and money, so we wanted a solution that could work for us now — something not too expensive but nice enough that we’ll be happy with it for the next year or so until we can circle back around to opening up the ceiling.

Enter this DIY lantern light fixture:

DIY IKEA Lantern Lighting

Other than sketching out how I wanted it to look and picking out the lanterns themselves, the GC gets all the credit for this creation. I asked him to give me a step by step description of how he did it, so it’s about to get a bit technical up in here:

Disclaimer: GC is an electrical engineer who has a lot of experience doing electrical work like this. I don’t recommend anyone without the proper training and background attempt the following, and even then, it’s at your own risk. Also remember whenever you do work with electrical like this, make sure to turn off your power and use a volt meter to make sure it’s off!

After taking out the old light fixture, we measured the distance between the two joists and cut down a 2×4 to fit in the space as framing.

Cut 2x4s

We screwed these 2×4 pieces on to the joists.

Framing

And attached the each electrical junction box to the framing with screws.

Junction Box

Then, we spliced the existing wiring to a new piece of 14-2 Romex cable (this was then linked to junction box #2) and secured the existing wire on junction box #1. Here’s a shot of junction box #1 after the wiring:

Wired Junction Box

Once the wiring was complete, time to move on to the the gaping hole in the ceiling left from the former rectangular light. Again, because time and patience were at a premium, we didn’t want to try to patch the hole left from the former light. Instead, we opted to cover it with a larger piece of pine, which we cut to 10 inches wide and 4.5 feet long. We measured this up with the junction boxes and cut out two 4×4-inch holes with a Jigsaw to accommodate them. Then we painted it with some leftover white interior paint I had used on a door in my condo.

IKEA’s Orgel pendant lamp was my lighting of choice; unfortunately, the Orgel is a plug and cord lamp and not a hardwired one that we could hook up directly to the junction box. So here’s where being engaged to an electrical engineer comes in handy again: he cut the plug end of the cord, drilled a hole in a plastic coverplate and fed the cord through it, then spliced the wires from the cord into the junction boxes.

Lighting Cords

It took a few tries to get the cord length right (he actually went back and re-cut the cord on the left), but we got it high enough so that the lanterns wouldn’t hit anyone on the head when you walk under them. Then we screwed the coverplates to the pine cover and ta-da!

IKEA Lanterns

Oliver was impressed.

Oliver

Or maybe scared? It’s hard to judge by that look. Either way, we were really happy with the final product!

Ceiling After

Does anyone else have a good-enough-for-now-but-not-forever project in their house?

Advertisements

over the moon

I’ve been seriously neglectful in telling you about our adventures in painting.

I had been throwing around some ideas in my head for what to paint the living room since we moved in. I wanted something light and neutral, maybe just an off white or taupe. But then I started to think that a really, really light yellow could complement the color scheme I have going/want to have going on.

Normally, I would have debated about color selection for weeks, maybe months. The room basically may have never gotten painted. I’m just too indecisive! Then a few weeks ago Sherwin-Williams put all their paint on sale for 30 percent off. And though it’s hard for me to make decisions, it’s even harder for me to pass upon a sale, so we took the plunge and bought two gallons of their Super Paint color-matched to Behr’s Moon Mist.

Would you believe I’ve never painted a room before? Not even a wall.

Cutting In

This painting stuff is no joke! Holy arm workout! And that’s just from the little bit of painting I did do. Major props go to the GC who took on quite a bit of this project while I was sitting on the couch watching Property Brothers supervising.

I will, however, take credit for taping off the whole room.

Taping

Because of our schedules, I’d say this took about a week and a half to get to the finished product:

Living Room After

I’m really happy with the color. It’s actually slightly lighter than it appears in the photo, but the effect is very bright and happy. Yes, I think I’ll be making all my interior design choices based on if they are happy or not.

Now that painting is complete, here are some more living room to-dos:

-Paint trim
-Make artwork for walls (in progress)
-Figure out what to do with the gaping hole next to the chair
-Buy something to put over the fireplace
-Redo the fireplace brick?

Have you done any house painting lately? Good news if you have upcoming projects: Sherwin-Williams is having another 30 percent off sale until July 8!